To form accurate corrugations in light-gauge materials, the F228-F229 set can be used. Spring-pressure pads assure positive stripping and release wedges prevent marring of the formed material.
Please type your preferred length: ft
Flame Hardening:
Yes
No
F230-F231 and F232-F233
For high production, continuous corrugating, and where consistent accuracy is necessary, the F230-F231 or F232-F233 set is recommended. The F230-F231 is for continuous radius corrugating and die set F232-F233 is for continuous angular corrugating. After the first operation, the spring-loaded pad locates the sheet and the dies become self-gauging.
Closed curls of 1/2" inside diameter and larger can be produced with die sets F100-F101 and F102-F103 in three strokes. Open curls up to 200 degrees can be produced in die set F100-F101 alone, in 2 operations.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2011/A/32/45°
F104-F105 and F106-F107
Die sets F104-F105 and F106-F107 form a curl over a wire core or mandrel in 3 operations. There may be a slight flat on the curl along the closing edge for sets shown on this page.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2030/30°
V = 16 mm
V = 20 mm
V = 25 mm
F108-F109
An off-center curl is completed in 3 strokes in die set F108-F109. Curls may range in size from 1/4" diameter to 3/4" diameter in 16 gauge and lighter stock. This type of curling die can be furnished without heels; however, we do not recommend this practice.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2035/35°
V = 8 mm
V = 12 mm
H = 80 mm
H = 120 mm
F110-F111
Off-center curls are performed in 3 strokes in die set F110-F111 and on-center curls in 4 strokes. On-center will not be perfectly round unless a mandrel is used in the last operation. Curls may range in size from 1/4" inside diameter to 3/4" inside diameter in 16 gauge and lighter. The range can be increased slightly if a mandrel is used.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2045/45°
V = 10 mm
V = 12 mm
F112-F113 and F114-F115
Die sets F112-F113 and F114-F115 produce the tightest and roundest curl that can be formed in two strokes within the range of 3/16" to 3/4" inside diameter. Dies can be mounted side by side for progressive forming if the press has sufficient length. In forming heavy gauge material, it is advisable to add a tool steel insert.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2060/60°
V = 6 mm
V = 8 mm
V = 10 mm
V = 12 mm
V = 16 mm
V = 20 mm
V = 25 mm
H = 80 mm
H = 120 mm
F114C-F115C
Die set F114C-F115C produces an on-center curl in an extra stroke. The roundness of the on-center curl becomes somewhat distorted unless a mandrel is used in the last operation.
Please type your preferred length: ft
Flame Hardening:
Yes
No
2130/A/30°
V = 6 mm
V = 8 mm
V = 10 mm
V = 12 mm
V = 16 mm
V = 24 mm
F116-F117 and F118-F119
Die sets F116-F117 and F118-F119 should be considered when a highly accurate on-center curl is desired. These dies may be used to produce a curl from 1/4" to 1/2" inside diameter in light gauge material. A minimal flat appears on the lead edge and the sheet remains relatively flat during the forming operation. The sheet to be formed must be wide enough to provide for a reasonable amount of stock to extend in front of the die sets for safe feeding of the part.
The die holders shown represent some of the types available. These items are offered in various sizes and shapes to suit any press requirement. Fastening means will be provided upon request. Top
